Browsing Sivas Cumhuriyet Üniversitesi Teknoloji Fakültesi by Title
Now showing items 20-39 of 100
-
Biosorption of methyl orange from aqueous solution with hemp waste, investigation of isotherm, kinetic and thermodynamic studies and modeling using multigene genetic programming
(SPRINGER INT PUBL AGGEWERBESTRASSE 11, CHAM CH-6330, SWITZERLAND, 16.08.2022)Water resources around the world are getting polluted day by day due to the rapidly developing industry. Industrial wastes have caused serious damage to the environment in recent years. Especially, dyes are waste products ... -
Brain tumor classification by using a novel convolutional neural network structure
(2022)Brain tumors located in the skull are among the health problems that cause serious consequences. Rapid and accurate detection of brain tumor types will ensure that the patient receives appropriate treatment in the early ... -
Characterization of mechanically alloyed Fe based and MoNiAl+Al2O3 reinforced composites
(https://www.degruyter.com, 2021)Fe-MoNiAl-Al2O3 powders were mechanically alloyed by a SPEX type attritor. The Fe based composite samples were reinforced with complex mechanically alloyed Fe-MoNiAl-Al2O3 particles in different ratios and Fe matrix ... -
Classification of brain tumors from MR images using deep transfer learning
(2021)Classification of brain tumors is of great importance in medical applications that benefit from computer-aided diagnosis. Misdiagnosis of brain tumor type will both prevent the patient from responding effectively to the ... -
Classification of plutonic rock types using thin section images with deep transfer learning
(2021)Classification of rocks is one of the basic parts of geological research and is a difficult task due to the heterogeneous properties of rocks. This process is time consuming and requires sufficiently knowledgeable and ... -
Conical Channel Design in AA7075/AZ91 Materials Joining with Mechanical Locking Method (MLM)
(2022)In industrial applications, materials with different chemical and physical properties are used by joining them. The main purpose is to achieve high performance at the most affordable cost by joining the superior properties ... -
COOLING OF CIRCUIT ELEMENTS WHOSE TEMPERATURES INCREASED DEPENDING ON THE FIN POSITIONS IN AN IMPINGING JET-CROSS FLOW CHANNEL
(2021)Gelişen teknoloji sayesinde devre elemanlarının boyutlarının küçülmesi ve artan işlemci kapasite ve hızları, elektronik elemanların sıcaklıklarının artmasına sebep olmaktadır. Cihazın sürdürülebilir bir şekilde çalışmasının ... -
COOLING OF HEATED SURFACES IN COMBINED JET FLOW CHANNELS WITH DIFFERENT FIN POSITIONS AND SiO2-WATER NANOFLUID
(15.01.2023)The increase in energy prices around the world negatively affects production costs, especially in the heat-intensive industry. However, the increase in the amount of heat production per unit volume in electronic devices ... -
Deep learning prediction of motor performance in stroke individuals using neuroimaging data
(Elsevier Science Direct, 12/04/2023)The degree of motor impairment and profile of recovery after stroke are difficult to predict for each individual. Measures obtained from clinical assessments, as well as neurophysiological and neuroimaging techniques have ... -
Determination of COPD severity from chest CT images using deep transfer learning network
(2022)The purpose of this study is to present a solution to the problem of detecting the severity of Chronic Obstructive Pulmonary Disease (COPD) from chest CT images using deep transfer learning network. The study has a novelty ... -
Determination of Pneumonia in X-ray Chest Images by Using Convolutional Neural Network
(2021)Pneumonia is one of the major diseases that cause a lot of deaths all over the world. Determining pneumonia from chest X-ray (CXR) images is an extremely difficult and important image processing problem. The discrimination ... -
Economic and environmental assessment of ground source heat pump system: The case of Turkey
(Elsevier, October 20)The use of renewable energy sources increases day by day. Although ground source heat pump systems are used to meet buildings' heating and cooling demands worldwide, high initial setup costs limit the widespread use of ... -
Effect of alloying elements on mechanical behaviour of Cu-Zn-Sn bronzes
(WALTER DE GRUYTER GMBHGENTHINER STRASSE 13, D-10785 BERLIN, GERMANY, 8 March 20)The effect of Fe, P and Mn on microstructure and fatigue properties of CuZnSn bronzes investigated with optical microscopy and scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction, hardness, ... -
Effect of Austempering Treatment on Metallurgical Structure of Ce Inoculated X210Cr12 Cold Work Tool Steel
(http://www.degruyter.com, 21 Februar)The effect of austempering treatment on metallurgical structure of X210Cr12 cold work tool steel inoculated with Ce was researched. Microstructural changes, elemental characterizations, and phase formations of the samples ... -
Effect of FeTi-FeB Inoculation on Shape of Carbide Reinforcements in Hypoeutectic High Chromium White Cast Irons
(http://www.degruyter.com, 16 March 2)FeTi-FeB was added to molten high chromium white cast iron in amounts of 0.5–2.5 wt% at 50 °C above the melting temperature. The samples were produced in four groups. The first group samples were investigated as cast, the ... -
Effect of Ni on microstructure and wear behaviour of 13Cr-W-Mo-2C white cast iron
(CONSEJO SUPERIOR INVESTIGACIONES CIENTIFICAS-CSICEditorial CSIC, C/VITRUVIO 8, 28006 MADRID, SPAIN, 30 June 20)The effect of Ni concentration on the microstructure and wear performance of 13Cr-(0.5-7.0) Ni-W-Mo-Mn-2C white cast iron subjected to homogenization heat treatment was examined. Concentration of Ni was altered in the range ... -
Effect of piston geometry on combustion characteristics of CI engine used Sal seed oil
(2023)The effect of piston bowl geometry on reducing soot emissions, improving combustion, and in-cylinder flow movements in a direct injection diesel engine was investigated. Standard combustion chamber (SCC) and newly modified ... -
Effect of rotary friction welding on mechanical properties of 6060 Al alloy
(https://revistademetalurgia.revistas.csic.es, 2021)6xxx series of aluminum alloys are prone to cracking when fusion welded without a proper filler metal. Alternatively, these alloys can be welded by rotary friction welding, a solid-state welding process, without using ... -
Effect of Thermomechanical Process on Mechanical Properties of CuZn10 Alloy
(http://www.degruyter.com, 07 July 20)The effects of thermomechanical processing on the grain size, tensile strength, and strain rate of a CuZn10 alloy were investigated. Microstructures of thermomechanically treated samples were introduced using a scanning ... -
ELMAS-SU NANOAKIŞKANI KULLANILAN FARKLI KANATÇIK UZUNLUKLU VE AÇILI BİRLEŞİK JET AKIŞLI KANALLARDA ISI TRANSFERİNDEKİ İYİLEŞMENİN ANALİZ EDİLMESİ
(15.01.2023)Especially in the energy-intensive industrial sector; attention is paid to ensure that all kinds of devices and equipment produced are systems with high energy efficiency and long life. The most important obstacle in front ...
