Comparison of the Effect of the Same Polishing Method on the Surface Roughness of Conventional, CAD/CAM Milling and 3D Printing Denture Base Materials

Basit Öğe Kaydı
dc.contributor.authorDemirkol, Didem
dc.contributor.authorTuğut, Faik
dc.date.accessioned2024-10-26T17:51:28Z
dc.date.available2024-10-26T17:51:28Z
dc.date.issued2023
dc.departmentSivas Cumhuriyet Üniversitesi
dc.description.abstractObjectives: The aim of this study was to evaluate the effect of both the same polishing method and those with and without thermal aging on the surface roughness of conventional, CAD/CAM milling and 3D printing denture base materials. Materials and Methods: A total of 30 round shaped specimens were obtained by 3 different methods: Conventional, CAD/CAM milling and 3D printing. After applying the same polishing technique to all groups, surface roughness values were measured. Profilometer device was used for surface roughness measurement. Then, after the thermal aging of all samples, surface roughness values were measured and the roughness values between no-thermocycling and thermocycling were compared. Tukey, Mann Whitney U and Kruskal Wallis tests were used statistically. P values of ? 0.05 were considered significant. Results: As a result of the same polishing process, there was a difference in surface roughness in all groups. While the highest surface roughness values were seen in 3D printing, the lowest roughness value was seen in the CAD/CAM milling and was statistically significant. Thermocycling did not show a statistically significant difference in surface roughness. Conclusions: The same polishing process caused different surface roughness values in the denture base materials obtained with different methods, and the lowest surface roughness value was seen in the CAD/CAM milling. © This work is licensed under Creative Commons Attribution 4.0 International License
dc.description.sponsorshipScientific Research Project Fund of Sivas Cumhuriyet University, (DİŞ-2022-296)
dc.identifier.doi10.7126/cumudj.1317851
dc.identifier.endpage286
dc.identifier.issn2146-2852
dc.identifier.issue3
dc.identifier.scopus2-s2.0-85173996423
dc.identifier.scopusqualityQ4
dc.identifier.startpage281
dc.identifier.trdizinid1216541
dc.identifier.urihttps://doi.org/10.7126/cumudj.1317851
dc.identifier.urihttps://search.trdizin.gov.tr/tr/yayin/detay/1216541
dc.identifier.urihttps://hdl.handle.net/20.500.12418/26241
dc.identifier.volume26
dc.indekslendigikaynakScopus
dc.indekslendigikaynakTR-Dizin
dc.language.isoen
dc.publisherCumhuriyet University Faculty of Dentistry
dc.relation.ispartofCumhuriyet Dental Journal
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanı
dc.rightsinfo:eu-repo/semantics/openAccess
dc.subject3D Printing; CAD/CAM Milling; Denture base material; Polishing; Surface Roughness
dc.titleComparison of the Effect of the Same Polishing Method on the Surface Roughness of Conventional, CAD/CAM Milling and 3D Printing Denture Base Materials
dc.title.alternativeKonvansiyonel, CAD/CAM Kazıma ve 3D Baskılı Protez Kaide Materyalleri Üzerine Uygulanan Aynı Polisaj Yönteminin Yüzey Pürüzlülüğüne Etkisinin Karşılaştırılması
dc.typeArticle

Dosyalar

Koleksiyon

Scopus İndeksli Yayınlar Koleksiyonu
TR-Dizin İndeksli Yayınlar Koleksiyonu